series am6 tw-r vz 6 watt | dc - dc converter www.aimt ec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r 13.b 1 of 3 north america only features: mo dels single output models dual output model input voltage (v) output voltage (v) output current max (ma) capacitive load, max (f) efficiency (%) am6 tw - 2412d - rvz 9 - 36 12 2 50 100 8 1 am6 tw - 2415d - rvz 9 - 36 15 200 68 80 am6tw - 4812d - rvz 18 - 72 12 250 100 78 am6tw - 4815d - rvz 18 - 72 15 200 68 75 i nput specifications parameters nominal typical maximum units voltage range 24 9 - 36 vdc 48 18 - 72 filter (pi) network absolute max rating 24 vin - 0.7 - 40 vdc 48 vin - 0.7 - 80 isolation specifications parameters conditions typical rated units tested i/o voltage 3 sec 1500 vdc resistance > 100 0 mohm capacitance 60 pf output specifications parameters conditions typical maximum units voltage balance balanced load 1 % voltage accuracy 1 % short circuit protection continuous short circuit restart auto recovery line voltage regulat ion 0.5 % load voltage regulation 0.5 % temperature coefficient 0.02 %/ o c ripple & noise at 20mhz bandwidth 60 mv p - p ? wide input range (4:1) ? operating temperature - 40 o c to + 85 o c ? 2 4 pin d ip package ? input / output isolation 1 5 00 vdc ? m etal package ? pin comp a t i ble with multiple manufacturers ? high efficiency up to 82 % ? continuous short circuit protection model input voltage (v) output voltage (v) output current max (ma) capacitive load, max ( f) efficiency (%) am6 tw - 2412s - rvz 9 - 36 12 500 470 8 2 am6 tw - 2415s - rvz 9 -36 15 400 330 80 am6 tw - 4812s - rvz 18 - 72 12 500 470 7 8 am6 tw - 4815s - rvz 18 - 72 15 400 330 7 8
series am6 tw-r vz 6 watt | dc - dc converter www.aimt ec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r 13.b 2 of 3 north america only general specifications parameters conditions typical maximum units s w itching frequency 100% load 100 - 400 khz opera ting temperature full load (see d erating chart) - 40 to +85 o c storage temperature - 40 to +125 o c max case temp era ture 100 o c cooling free air convection humidity 95 % case material nickel coated copper weight 15 g dimensions (l x w x h) tolera nce 0.5 mm or 0.02 inches 1. 25 x 0. 8 x 0. 4 inches 31.75 x 20.32 x 10.16 mm mtbf > 2,200,000 hrs (mil - hdbk - 217f, ground benign, t=+25 o c) safety specifications parameters standards designed to meet iec 60950 - 1 note: all specifications in this datasheet are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. pin out specifications dimensions 31.75 (1.25) 20.32 (0.80) 2.54 (0.10) 5.08 (0.20) printed face built-in stand-offs to ease pcb cleaning 10.16 (0.40) 3.05 (0.12) 0.50 (0.02) 15.24 (0.60) 22.86 (0.90) bottom view 2 3 9 11 14 16 22 23 pin 1500 vdc single dual 2 - v input - v input 3 - v input - v input 9 no pin comm on 11 n.c. - v output 14 +v output +v output 16 - v output common 22 +v input +v input 23 +v input +v input
series am6 tw-r vz 6 watt | dc - dc converter www.aimt ec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r 13.b 3 of 3 north america only der ating 0 25 75 50 85 100 80 60 40 20 0 85 o c safe operating area free air convection ambient temperature o c 100 -40 output power % note: 1. datasheets are upda ted as needed and as such, specifications are subject to change without notice. once printed or downloaded, datasheets are no longer controlled by aimtec; refer to www.aimtec.com for the most current product specifications. 2. product labels shown, inclu ding safety agency certifications on labels, may vary based on the date manufactured. 3. mechanical drawings and specifications are for reference only. 4. all specifications are measured at an ambient temperature of 25c, humidity<75%, nominal input volt age and at rated output load unless otherwise specifie d. 5. aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. cas numbers and other limited information are considered proprietary and may not be available for release. 6. this product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control s ystems or other such applications which necessitate spec ific safety and regulatory standards other the ones listed in this datasheet. 7. warranty is in accordance with aimtecs standard terms of sale available at www.aimtec.com.
|
